Edgar's Painting and Handyman Services, LLC
Overview Services About Terms Privacy
$60–$125 USD / HOUR DIRECT RATE / OWNER-OPERATED BY EDGAR A. OSPINA / RESIDENTIAL & LIGHT-COMMERCIAL REPAIRS / BRIDGEPORT & FAIRFIELD COUNTY / 12-MONTH WORKMANSHIP GUARANTEE /
Bridgeport & Immediate Surrounds Standard 2-Hour Dispatch Minimum Same-Day or Booked Slots

We price all physical handyman and finish carpentry work from sixty to one hundred twenty-five dollars per hour.

Every job is performed under the direct supervision of Edgar A. Ospina. Materials and structural anchors are billed at direct supplier receipt cost with zero hidden surcharges.

Rate Range $60–$125 USD / hr (Rate depends on job height, structural complexity, urgency, and equipment requirements)
Request Work Calculate Wall Load
Installing wall cabinets along a precision laser level line.
Structural mounting into timber studs along laser datum lines.

Heavy kitchen cabinets and articulated TV arms cannot rely on hollow drywall plugs. We project continuous laser lines, anchor directly into two-by-four timber studs with structural wood screws, or install heavy-duty quarter-inch Snaptoggles rated for forty pounds shear each in half-inch sheetrock.

  • Rate: $60–$125 USD/hr + anchors
  • Duration: 1.5 to 3.0 hours
  • Fasteners: GRK Timber / Snaptoggle 1/4"
Handyman chiseling a hinge mortise into an interior timber door.
Hand-mortised hinge pockets and true perimeter door margins.

When a solid timber interior door rubs the head jamb or refuses to latch, we cut mortises with hand wood chisels, shim settled hinges, and reset the strike plate flush. We replace one-inch factory hinge screws with three-inch structural screws driven through the jamb and into framing studs.

  • Rate: $60–$125 USD/hr
  • Duration: 1.5 to 2.5 hours per door
  • Clearance: 1/8" uniform perimeter
Drywall technician feathering joint compound over patched sheetrock.
Multi-coat drywall feathering with HEPA dust containment.

Ceiling water leaks and wall penetrations require solid timber backer blocks and fiberglass mesh tape embedded in setting compound. We apply three thin coats feathered out twelve inches past the seam and sand with Festool HEPA extractors so your home stays free of gypsum powder.

  • Rate: $60–$125 USD/hr + compound
  • Visits: 2 visits (dry time)
  • Finish: Level 4 primer-ready
Repairing exterior roofline fascia and trim on an extension ladder.
Rotten cedar fascia replacement with stainless ring-shank nails.

Connecticut winter snow and ice dams rot roofline fascia and soffit timber. We strip compromised wood back to solid rafter tails, install factory-primed Western Red Cedar or cellular PVC, fasten with 316 stainless ring-shank nails, and seal all end-grain cuts with polyurethane sealant.

  • Rate: $60–$125 USD/hr + stock
  • Ladder: Werner Type IA fiberglass
  • Sealant: Quad Max exterior poly
Plumber replacing corroded water supply shutoff with brass ball valve.
Quarter-turn brass ball valve swaps under sinks and vanities.

Corroded gate valves fail when you need to isolate a leak. We cut back corroded copper or iron supply lines, install modern solid-brass compression ball valves, replace worn rubber hoses with braided stainless steel, and pressure-test the assembly under domestic main pressure.

  • Rate: $60–$125 USD/hr (2-hr min)
  • Testing: 20-min static pressure
  • Hardware: BrassCraft 1/4-Turn Valves

Fastener & Wall Working Load Calculator

Calculate safe structural working capacity for wall-mounted shelving, floating vanities, heavy framed mirrors, or TV wall plates. This tool compares your fixture weight against real fastener shear limits in timber studs and hollow sheetrock.

Formula: Safe Load = ((Stud Screws × 75 lbs) + (Toggle Anchors × 40 lbs)) ÷ Safety Factor (2.0 static / 3.0 shelf)
45 lbs
Combined weight of shelf board plus all books, dishes, or equipment resting on it.
2 studs
Requires #10 × 2-1/2" wood screws driven at least 1.5" into solid Douglas fir or SPF lumber.
0 toggles
1/4"-20 Toggler Snaptoggles anchored through hollow drywall spans between studs.
50 lbs Safe Capacity
1.1× Safety Factor
STRUCTURALLY SOUND: Fasteners distribute load cleanly across framing timber.

Approved trade configuration. Fasteners distribute load cleanly across framing timber and anchored substrate.

Hardware Bill of Materials
  • 2× #10 × 2-1/2" Structural Wood Screws (pre-drill with 1/8" bit)
Use This Spec In Estimate Request

Calculations assume plumb vertical wall substrate and properly seated fasteners. If no framing studs can be reached for loads over 50 lbs, a horizontal timber ledger board bolted across framing is mandatory.

Clear rates, step-by-step dispatch, and trade policies

We operate transparently at 132 Federal St in Bridgeport. Here is how dispatch is scheduled, what invoices look like, and who is not suited for our service model.

Our Dispatch & Arrival Process

Step by Step

Step 1: Scope Intake. You submit your repair details online or call (203) 246-7578. Edgar reviews wall materials, fixture weight, and access height.
Step 2: Time Window Confirmation. We provide a specific arrival window honored to the quarter-hour, bringing all necessary fasteners, ladders, and HEPA vacuums.
Step 3: Site Protection. We lay drop cloths and set zip-wall containment before striking any wall or mortising timber.
Step 4: Mechanical Execution. Repairs are executed to framing tolerances and verified under static load or line pressure.
Step 5: Itemized Invoicing. You receive an itemized receipt showing the exact hours worked at $60–$125/hr, plus raw supplier receipts for hardware.

Who our service is not for

Honest Boundaries

If you are looking for an anonymous cash-in-hand worker who will hang a seventy-pound TV on plastic drywall anchors with drywall screws to save twenty dollars, we are not your contractor. We refuse shortcuts that fail inside wall cavities. We are also not a commercial general contracting firm quoting sixty-thousand-dollar kitchen gut renovations. We handle focused physical repairs done properly.

Request Work & Schedule Repair

Fill out your repair details below. Edgar Ospina reviews all job requests directly from our Bridgeport shop.

All work billed at our confirmed $60–$125 USD/hr schedule with a standard 2-hour callout minimum. No binding quote without physical site assessment.